Rapiro Forum

Ask questions and share your thoughts about Rapiro.

If you have project or knowlege, please share it on newly opened Wiki.

Rapiro servos not calibrating

Help! I have this issue with Rapiro and wonder if anyone else has, or has any suggestions...There seem to be some issues with the servo’s...
1 comments posted by hannah.fawcett.775 comment from ken.suzuki.902 on 2014-06-23 15:15


コマンド#M8を転送してもRapiroは左腕を上げただけでジーという音が鳴るまま とまったままです。(lefthand1.jpg) また、電源OFFにして左手を上にあげ(lefthand2.jpg)、電源をONにすると 正常にリセットされます。(lefthand3.jpg...
7 comments posted by takeshi.nagahisa comment from takeshi.nagahisa on 2014-06-15 22:11


4 comments posted by KeigoFukuda comment from shinichirou.saito on 2014-06-12 10:08

RASPBERRY PiからRAPIROへのコマンド送信について

やっとRAPIROがくみ終わって、微調整もすんで、 RaspberryPiからPythonを使ってRAPIROを動かそうとしていたのですが まったく動きません。 RaspberyPiからcuでも行ってみましたが、接続はできているようなのですが コマンドを受け付けてないように...
2 comments posted by 木村隆博 comment from 木村隆博 on 2014-06-05 01:53

raspberry piからrapiroにコマンドが送れません。

Raspberry piとrapiroの制御基板を接続し、raspberry piからpythonを使ってコマンド#M1から#M9を送信したところ、始めのコマンドのみを受け付けて、後のコマンドは無視してしまいます。どのような現象が起きているか見当がつかないのでどなたか知見が...
2 comments posted by takeshi.nagahisa comment from takeshi.nagahisa on 2014-06-01 00:09

Initial adjustment of servo angle

> Please turn on the switch to make Initial adjustment of servo angles. > All servo axes are rotated to initial angles. I execute...
3 comments posted by tatsuya.kubota.395 comment from tatsuya.kubota.395 on 2014-05-25 00:58


2 comments posted by kenji.iwamoto.5876 comment from kenji.iwamoto.5876 on 2014-05-24 10:56

Initial alignment - help required!

1) I connected the fully charged 5 Sanyo batteries. 2) Connected the RAPIRO via USB to micro USB cable to Laptop. 3) Installed Port drive...
2 comments posted by sp760712 comment from sp76071254e451679ace4e6f on 2014-05-23 17:52

Control the LED color Without power the other servo

Is there a way to do so? this is a very simple python script to change to RAPIRO's eye color. i put a simple Loop and th crew some rando...
4 comments posted by djakku_u comment from oga on 2014-05-12 22:29

Output voltage vs. Load current chart of LDO on Rapiro Board

1 comments posted by oga comment from oga on 2014-05-12 22:16


http://wiki.rapiro.com/ We opened wiki. Anybody can register and create/edit pages. Please contribute your knowledge of Rapiro.
5 comments posted by ken.suzuki comment from ken.suzuki on 2014-05-12 10:37

another approach on motion editior

Hi was thinkering on how to create motions for the robot. Altought the original sketch has some limitation, its shouldn't stop us for cre...
0 comments posted by djakku_u on 2014-05-11 23:20

I think I fried my rapiro board...

I was using a 12v 90w power supply and tried to connect a load to the 5V on the I2C pins. I was connecting this because I noticed the ou...
3 comments posted by evilbluechicken comment from oga on 2014-05-11 09:30

Rapiro remote control projects

I have completed three projects to remotely control using the Arduino Sketch that added the #H case to turn servo power off. It can be d...
0 comments posted by brad98408794610288b0340d0 on 2014-05-08 11:51

Can I buy just the parts I need?

I have a 3D printer, a Raspberry Pi, Pi Camera, and tons of servo's already. Is it possible to buy just the other parts (i.e. the Rapiro ...
2 comments posted by lairdp comment from ken.suzuki on 2014-05-07 10:32


ラピロにUSB以外で推奨スピーカーとマイクを繋げたいですが具体的な方法が知りたいです。 サイトを見てもスピーカの接続方法がわかりません。
4 comments posted by takeo.myojin comment from shinichirou.saito on 2014-05-03 16:03

Interface Raspberry pi with Arduino

Hi, I am trying to control the Arduino through Raspi. I was planning to send some sort of signal through serial connection when a particu...
0 comments posted by adityakaushik00c8086ed3ca6b4bcc on 2014-05-03 00:09

Raspberry and rapiro

Hello have maybe a fool question but I want to understand how to configure rapiro with raspberry. I read this tutorial: http://elinux.or...
2 comments posted by coerrace comment from coerrace on 2014-05-01 20:59

How do you connect "COM-09151 Speaker - 0.5W 8Ohm" to raspberry pi?

Hi, I'm trying to connect the speaker (http://www.abra-electronics.com/products/COM%252d09151-Speaker-%252d-0.5W-8Ohm.html) to raspberry ...
3 comments posted by hanzhao comment from ken.suzuki on 2014-04-30 18:33

Painting the robot?

What kind/type/brand of paint would work in its surface? Thank you :)
2 comments posted by kobe_23 comment from kobe_23 on 2014-04-25 22:55