My Aurdino Code will not download

When I download the standard firmware gives me a weird message.

Arduino: 1.6.7 (Mac OS X), Board: "Arduino/Genuino Uno"

Sketch uses 10,512 bytes (32%) of program storage space. Maximum is 32,256 bytes.
Global variables use 1,744 bytes (85%) of dynamic memory, leaving 304 bytes for local variables. Maximum is 2,048 bytes.
Low memory available, stability problems may occur.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00
Problem uploading to board. See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

This report would have more information with
"Show verbose output during compilation"
enabled in File > Preferences.

All in red. I appreciate it in advance for the person that helps me with my problem.

posted by chebrolu.rishi on 2016-02-29 07:36
3 comments

posted by chebrolu.rishi on 2016-02-29 07:37

Hello

i got the same problem. Never had this trouble when I started programming RAPIRO 4 years ago. Then I didi not try again since. But today, no way to connect to the blue eye RAPIRO. It is as if the Arduino board (set as a arduino uno as instructed in the manual) was not recognized anymore.
Someone can help? May be the programmer setting should not be AVRISP mkII?

posted by chocronolivier on 2020-01-04 01:23

Hello,

If you can not upload the RAPIRO firmware by Arduino IDE, Did you adjust the port speed 57600 bit/sec, USB Serial Port (COM3), in my case?

For another problem, You may see trouble shooting following URL, sorry you may need language translate with google:
http://www.asahi-net.or.jp/~cb9i-kn/geek/20170521rapiro2.html

posted by ichiro.kano2 on 2020-05-24 11:25

( Allowed tags: <b> <s> <code> <blockquote> <img> . Automatic URL link.)

Uploaded image is placed to the bottom of the post. To add multiple images, make post once then edit the post.

Read Terms of Service upon submitting. 投稿する前に利用規約をお読みください。